跳至主要内容

Maintenance of manual busbar processing machine and CNC busbar processing machine

 The punching dies for CNC busbar processing equipment can be divided into three types.

The punching die of turret CNC busbar processing equipment is used to process various specifications of copper bar, an aluminum bar, and other bus bars. As long as in the corresponding processing unit. The bus bar can be punched separately, which is matched with the CNC busbar processing. Specifically, there are several structural types, such as circular and elliptical.

The punching die of the copper aluminum busbar is durable, with high punching precision and a smooth surface.

Maintenance of manual busbar processing machine and CNC busbar processing.

  1. The moving parts of punching, shearing, and bending units should be coated with lubricating oil before the shift, once in the morning and afternoon.
  2. The worktable and each unit shall be oiled before work.
  3. The punching die should be coated with lubricating oil once every 20 times of operation.
  4. A lubricating oil should be applied once every 20 working times of shear mold.
  5. When the bending die works 50 times, the lubricating oil shall be applied once.

Selection of CNC busbar processing.

The main quality and performance service depends on the scale and strength of the specific CNC busbar processing pieces of the equipment manufacturer. Normally speaking, the quality and performance of a good CNC busbar processing manufacturer with scale and strength are still good.

busbar processing machines


Lubrication is an important work to reduce the fault of the CNC busbar processing equipment. Only by doing well lubrication can bus bar machines be better used.

1. Apply lubricating oil to the moving parts before cutting and shift, once in the afternoon.
Observe the actual shear position through the observation holes of the upper and lower tool blocks.
Use the ruler slider to block the material and place the bus bar on the workbench. Determine the shear size, and then use the pressing handwheel to press the bus bar to prevent the data from warping and damaging the mold.
2. Punch and apply lubricating oil to the moving parts before the shift, once in the afternoon.
In the punching process, it is necessary to ensure the level of processing data.

The necessary matching mold should be selected. When punching, remember not to mix the upper and lower molds with different inner diameters. When machining long-distance holes, the upper and lower die directions must be consistent, otherwise, the mold will be damaged.

Lubrication can not only reduce the fault of CNC busbar processing equipment but also prolong the service life, which is an essential maintenance content.

评论

发表评论

此博客中的热门博文

The relationship between busbar machine and switchgears.

  Busbar machines and switchgears are two components that are often used together in electrical systems. Busbars are flat strips of copper or aluminum that are used to conduct electricity in power distribution systems, while switchgears are electrical equipment that controls the flow of electricity in a power system. Busbar machines are used to manufacture busbars of different sizes and shapes, which are then used in switchgears as conductors to distribute electrical power. The busbar machines can punch holes and cut busbars to specific sizes and shapes, which can be customized to fit the specific requirements of a switchgear. Switchgears are equipped with different types of busbars that are designed to carry specific electrical loads. These busbars are connected to the switchgear's main circuit breaker and are used to distribute electrical power to different parts of the electrical system. The use of high-quality busbars in switchgears is crucial to ensure the safety and reliabil...
发表评论
阅读全文

About CNC BUSBAR BENIDNG MACHINE.

  Introduction CNC busbar bending machines are specialized equipment used for the bending of busbars in the electrical industry. They provide a precise and efficient method of bending busbars to the required angles and shapes. In this blog, we will discuss the working process of a CNC busbar bending machine. Working Process Material preparation: The first step is to prepare the busbar material. The busbar material is typically copper or aluminum and is available in various sizes and thicknesses. The material is loaded onto the CNC busbar bending machine. Programming: The next step is to program the machine. The operator enters the required bending angle, length, and shape into the machine's computer. The machine can store multiple programs for different busbar shapes and sizes. Clamping: The busbar material is then clamped in place. The machine uses hydraulic clamps to secure the material in position, ensuring that it does not move during the bending process. Bending: The bending ...
发表评论
阅读全文