The temperature data of the multifunctional bus bar processor can be transmitted to the measuring instrument with low potential through an infrared light wave or radio wave. Since there may be several measuring points, the measured data has an address identification code for easy control. The disadvantage of infrared data transmission is that the optical wave transmission requires space without obstacles and the transmission distance is short, generally only 3m-5m.
The design has a copper chip integrated bag and an open mouth chip outlet. Slide type can collect and collect the cut and wear copper chip strip, so as not to spread everywhere and disorderly. The whole modeling is bright in color, the surface is painted and treated with phosphoric acid skin mold for rust prevention, and it is wear-resistant and impact resistant.
The plate seat can be adjusted directly by hand, which can provide the standard of long and short size and unified control specification. The position of the punching machine, bending plate tool and cutting tool is correctly determined by the accurate guidance of the control switch of the azimuth valve. A safe and firm footswitch, can control the oil inlet and return.
The control system can be studied and manufactured separately from the controlled object, and it must be treated as a whole, and the dynamic problems under high-speed state, and the time delay effect of optical and electrical signals under the condition of super high-speed motion control and the elimination of them are studied. In the high-speed situation, we must study the whole linkage of the CNC system and the control object, the nonlinear control strategy based on the whole dynamic point, and the intelligent control method. The bending unit of the multifunctional bus bar processor is horizontal processing, which is more safe and convenient in processing.
The three working stations of the multifunctional bus bar processor can work at the same time without affecting each other, greatly improving the working efficiency. The working stroke of each processing unit can be adjusted conveniently, the processing assistant time is reduced, the production efficiency is improved. The hydraulic oil tank is welded with a thick steel plate and Phosphated so that the hydraulic oil can not deteriorate for a long time. When installing, debugging (adjusting the gap between the dies and adjusting the blade), or disassembling the mold, the familiar personnel must carry out the normal operation of the machine according to the specified rules. Do not put the handle or part of the body between the upper and lower die (blades), so as to avoid any accident, all sundries and tools should not be placed on the workbench, so as to avoid accidents caused by rolling into the mold or knife edge.
The machine can be a multi-human Operation, so a special person must be responsible for directing the production. The clearance between the cutting blade and die and the radius of the bending fillet must be selected according to the thickness of the copper bar (or aluminum bar). When changing the die, it is necessary to stop the machine to avoid danger. When working with the workpiece, when waiting for the slide to go down, the blade and die edge sharpness must be checked regularly. If the edge is blunt, it should be checked regularly Repair or replace when it is used. When the multi-functional bus processing machine uses steel pipe as the suspender of lamps, the inner diameter of steel pipe shall not be less than 10 mm, and the thickness of steel pipe wall shall not be less than 1.5mm; for lamps installed in rows in the same room or place, the deviation of core line shall not be greater than 5mm; the selection of suitable transformer winding machine equipment for three-phase transformer is the key to produce high-performance transformer. Foil coil winding machine is used to make low-voltage winding machine Key equipment of foil coil. Tension control and deviation correction of the foil tape is the key technologies of the foil coil winding machine.
The tension of the foil band in the current domestic or imported foil coil winding machine is produced by mechanical friction, and the tension is not stable enough, which will cause the uneven tightness of the coil, the inconsistency of DC resistance between the coils, and the outer diameter of the coil. The larger the transformer capacity is, the greater the influence on the power grid, and the higher the security is required.
The performance of transformer manufacturing quality requires not only reliable electrical performance, mechanical stability, and short circuit resistance. The stability mainly shows that the manufacturing process control of the coil requires the electromagnetic balance of the high and low voltage coils, and the axial turns are close and evenly distributed. Therefore, it is required that the winding process of the coil should be compressed axially and the radial direction should be tightened. The vertical winding machine is used to make use of the weight of the wire cake, and the axial force is naturally compressed. The tension is controlled by the tension device in the radial direction.
评论
发表评论